Details of how to work with Rebetti: The method of completing Rebetti in a correct manner is described in the Stipes, Bars and Stipes.

Guilty PleasureBasics of Rebett SolvingSince then, the second stage of the programme has been put into practice. We have standardised our work methods to ensure quality, efficiency and personal safety of our rebates. In the past, we have been able to record our experience with hotels, rebates and concrete rebates, and have been able to identify the main stages of the rebate process, and have been able to use our experience with the vast majority of the masters to see them clearly.

Pre-preparation operation: For good service, it is necessary for Anata to make initial preparations by using his/her own tools and machine tools: hot plates: heating stoves (oil, gas or electric stoves), rebates, top gases, top hanands, klamps, spanners, and so on. Concrete: Rebreathers, Rebreathers, Rebreathers, Rebreathers, Hammers, Tops and Handles. General Tools: Air Drill, Electric Drill, Drill, Scrubs, Hammer, Extending Mirror, See This Board. Selection of Revette：に従って、the correct material, diameter and length of the Revette. Calculation formula for the length of the lift: L = δ + (1.3~1.5)d. δ is the full thickness of the plate, and d is the diameter of the lift. Preparation of the workpiece: Oil, soap, and bar on the connection surface. The workpiece is designed to be positionally resolved by the screw and the tooling is stopped by spooling.

Cleaning and heating of the cavity: The cavity of the rebate is cleaned in the air, and the wall of the cavity is confirmed to be slippery. Rebettes are heated in a furnace and heated equally at bright orange-red (about 1000-1100°C). The heating is carried out in a rapid and uniform manner, avoiding the effects of anakisugi and acidification. Neji cutting and coating: Heated rebates are inserted into the inserts by clamping and inserting into the nail holes at an early stage. One operator can use the upper part of the hurdles to make the rebate at the end of the rebate. Rebate Forming: The other operator sets the rebate by using the rebate gun to snipe at the protruding end of the rebate, initially at a light weight, and then at a heavier stroke to move the rebate and bury the nails. Next, the revolver and gun are vibrated around the centre of the nail bar, and the end of the bar is pressed against the half-circle-shaped apsite and head. The action is fast and accurate in the low temperature of the robot before the loss of plasticity. Conductor and Rebreather Operation Portfolio: Rebreathers are heated directly in the cavity. The head is formed by the use of a silver spoon, a silver spoon, or the use of a silver gun to induce the formation of a mandrel. The equipment and the strength of the robot are necessary for simple operation.

Thirdly, after the completion of the Rebate, the quality inspection and analysis of the defects will be carried out in order to check the appearance of the product: Appearance Inspection: The head of the AHPセット is in a regular shape, slippery, cracked, and the head of the product is concentric, and the distortion of the head is not good. Inch Inspection: The diameter and height of the head are checked for conformity with the specifications by using a sanitary plate. Chipping: Using a 0.1mm tape measure, the inserted surface of the workpiece is chipped and inserted to a depth of 20mm or more. More information about the product: Headset: Tip hurdles with Tip Positive angle of the Rebate Gasket. Rebate hibachi: The quality of the material is bad, and the heating is not appropriate (yaki overgrowth). The head is buried: the processing of the nail hole is not appropriate, the force of the lever is not very strong. Safety regulations include the use of protective eyewear, handbags, earplugs, and o-beams. High-temperature rebreathers can be used for fire prevention and to prevent fire injuries in high-temperature rebreathers. The use of revolving gases is prohibited in the workplace, and the use of gun ports is forbidden. The workplace is organised and tools are kept tidy.

Conclusion The standard operating method is a practical method for the competent robot and the melter. By combining theory and practice, and by observing and practicing, we can learn this technique. We have accumulated a great deal of experience, and we have described our experience in "Rebelt Welding Honda Blocks: A Highly Advanced Technology and a Solution to a Trouble-Shooting Problem" in our last journal, "Rebelt Welding Honda Blocks: A Highly Advanced Technology and Solution to a Trouble-Shooting Problem".